diff options
Diffstat (limited to 'rc.sysinit')
-rwxr-xr-x | rc.sysinit | 46 |
1 files changed, 23 insertions, 23 deletions
@@ -14,10 +14,10 @@ fi echo " " printhl "Arch Linux\n" -printhl "${C_H2}http://www.archlinux.org" +printhl "${C_H2}https://www.archlinux.org" printsep -# mount the api filesystems +# mount the API filesystems # /proc, /sys, /run, /dev, /run/lock, /dev/pts, /dev/shm mountpoint -q /proc || mount -t proc proc /proc -o nosuid,noexec,nodev mountpoint -q /sys || mount -t sysfs sys /sys -o nosuid,noexec,nodev @@ -34,7 +34,7 @@ if [[ ! -e /run/initramfs/root-fsck ]]; then # remount root ro to allow for fsck later on, we remount now to # make sure nothing can open files rw on root which would block a remount findmnt / --options ro &>/dev/null || - status "Mounting Root Read-Only" mount -o remount,ro / + status "Mounting root read-only" mount -o remount,ro / fi run_hook sysinit_start @@ -48,26 +48,26 @@ case $HARDWARECLOCK in esac if [[ $HWCLOCK_PARAMS ]]; then - stat_busy "Adjusting system time and setting kernel timezone" + stat_busy "Adjusting system time and setting kernel time zone" - # Adjust the system time for timezone offset if rtc is not in UTC + # Adjust the system time for time zone offset if rtc is not in UTC # 1. Make creation time on device nodes sane (FS#8665) # 2. Filesystem checks can depend on system time # 3. This also sets the kernel time zone, used by e.g. vfat - # If TIMEZONE is not set in rc.conf, the timezone stored in /etc/localtime - # is used. If HARDWARECLOCK is not set in rc.conf, the value in - # /var/lib/hwclock/adjfile is used (in this case /var can not be a separate + # If TIMEZONE is not set in /etc/rc.conf, the time zone stored in /etc/localtime + # is used. If HARDWARECLOCK is not set in /etc/rc.conf, the value in + # /var/lib/hwclock/adjfile is used (in this case, /var cannot be a separate # partition). [[ $TIMEZONE ]] && export TZ=$TIMEZONE hwclock $HWCLOCK_PARAMS && stat_done || stat_fail unset TZ fi -# Start/trigger UDev, load MODULES and settle UDev +# Start/trigger udev, load MODULES, and settle udev udevd_modprobe sysinit # this must be done after udev has loaded the KMS modules -status 'Configuring Virtual Consoles' /usr/lib/systemd/systemd-vconsole-setup +status 'Configuring virtual consoles' /usr/lib/systemd/systemd-vconsole-setup # bring up the loopback interface [[ -d /sys/class/net/lo ]] && @@ -77,11 +77,11 @@ status 'Configuring Virtual Consoles' /usr/lib/systemd/systemd-vconsole-setup [[ $USEDMRAID = [Yy][Ee][Ss] && -x $(type -P dmraid) ]] && status "Activating FakeRAID arrays" dmraid -i -ay -# BTRFS devices detection +# Btrfs devices detection [[ $USEBTRFS = [Yy][Ee][Ss] && -x $(type -P btrfs) ]] && - status "Activating BTRFS volumes" btrfs device scan + status "Activating Btrfs volumes" btrfs device scan -# Activate LVM2 groups if any +# Activate LVM2 groups, if any activate_vgs # Set up non-root encrypted partition mappings @@ -96,7 +96,7 @@ fi # Check filesystems run_hook sysinit_prefsck if [[ -x $(type -P fsck) ]]; then - stat_busy "Checking Filesystems" + stat_busy "Checking filesystems" fsck_all >|"${FSCK_OUT:-/dev/stdout}" 2>|"${FSCK_ERR:-/dev/stdout}" declare -r fsckret=$? (( fsckret <= 1 )) && stat_done || stat_fail @@ -108,25 +108,25 @@ run_hook sysinit_postfsck # Single-user login and/or automatic reboot if needed fsck_reboot $fsckret -status "Remounting Root and API filesystems" \ +status "Remounting root and API filesystems" \ /usr/lib/systemd/systemd-remount-fs -# now mount all the local filesystems +# Now mount all the local filesystems run_hook sysinit_premount -status "Mounting Local Filesystems" \ +status "Mounting local filesystems" \ mount_all run_hook sysinit_postmount -# enable monitoring of lvm2 groups, now that the filesystems are mounted rw +# Enable monitoring of LVM2 groups, now that the filesystems are mounted rw [[ $USELVM = [Yy][Ee][Ss] && -x $(type -P lvm) && -d /sys/block ]] && status "Activating monitoring of LVM2 groups" \ vgchange --monitor y >/dev/null -status "Activating Swap" swapon -a +status "Activating swap" swapon -a -[[ $TIMEZONE ]] && status "Configuring Time Zone" set_timezone "$TIMEZONE" +[[ $TIMEZONE ]] && status "Configuring time zone" set_timezone "$TIMEZONE" -status 'Initializing Random Seed' /usr/lib/systemd/systemd-random-seed load +status 'Initializing random seed' /usr/lib/systemd/systemd-random-seed load # Remove leftover files remove_leftover @@ -135,11 +135,11 @@ if [[ -s /etc/hostname ]]; then HOSTNAME=$(< /etc/hostname) fi if [[ $HOSTNAME ]]; then - stat_busy "Setting Hostname: $HOSTNAME" + stat_busy "Setting hostname: $HOSTNAME" echo "$HOSTNAME" >| /proc/sys/kernel/hostname && stat_done || stat_fail fi -stat_busy "Saving dmesg Log" +stat_busy "Saving dmesg log" if [[ -e /proc/sys/kernel/dmesg_restrict ]] && (( $(< /proc/sys/kernel/dmesg_restrict) == 1 )); then install -Tm 0600 <( dmesg ) /var/log/dmesg.log |